| Customization: | Available |
|---|---|
| Max Diameter of Workpiece: | <500mm |
| Mass Scope of Workpiece: | <900kg |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Method E1: Tensile performance
This measuring method applies to optical fiber cables which are tested at a particular tensile strength to examine the behavior of the attenuation and/or the fiber elongation strain as a function of the load on a cable which may occur during installation. This method is intended to be nondestructive (the tension applied shall be within the operational values).
Method E3: Crush
The purpose of this test is to determine the ability of an optical fiber cable to withstand crushing
Technical specifications
|
Load capacity |
kN |
100 |
|
Tensile capacity of Bow-type |
kN |
5 |
|
Crush capacity |
kN |
10 |
|
Accuracy class |
% |
±0.5% |
|
Measuring range |
% |
0.4%-100% |
|
Compression head |
|
100mm×100mm,hardness:HB240~280 |
|
Loading speed |
mm/min |
0.2~500 |
|
Deformation measuring accuracy |
% |
±0.5% |
|
Displacement measuring accuracy |
% |
±0.3% |
|
Elongation measurement |
|
1. gauge length: 1000mm 2. Measuring resolution is better than 10μm 3. Accuracy is better than ±0.5%. |
|
Crosshead travel |
mm |
800~1100mm |
|
Optical Fiber Cable Tensile Tester (both Normal and Bow-type Cable) |
|
Optical Fiber Cable Tensile Tester (Bow-type Cable) |
|
Optical Fiber Cable Crush Cut Tester |
|
Optical Fiber Cable Torsion Tester |
|
Optical Fiber Cable Impact Tester |
|
Optical Fiber Cable Repeated Bending Tester |
|
Optical Fiber Cable Winding Bending Tester |
|
Optical Fiber Cable Kink Tester |
|
Optical Fiber Cable Water Penetration Tester |
|
Optical Fiber Cable Temperature Cycling Chamber |
|
Optical Fiber Cable Abrasion Tester |
|
Optical Fiber Cable Flexing Tester |
|
GVT-1000 Optical Fiber Cable Sheave Testing Machine
|
|
GVA1000 Cable Aeolian Vibration Testing Machine |
|
GLA1000 Optical Fiber Cable Galloping Testing Machine
|
1. Application
Optical Fiber Cable Tensile Tester (Indoor Cable) are designed specifically for indoor (Bow Type) optical fiber cables to test
tensile strength under tension. The tester compliments with an extensometer to measure the cable.
Test cable sample is wound over the approximate sized sheave, pulled at a specific rate until a pre-determined tension is applied.
The test cable is further laid to rest under tension as per detail specifications, and then the attenuation and fiber length are
measured.
2.Specification:
Model : GLY-2 (Bow)
Load capacity: 2KN (other loads are available upon request)
Crosshead travel: 1000 mm
Loading speed: 0.2-500mm/min
IEC-60794-1-2-E2A Optical fiber cable abrasion tester
Application
The Optical fiber cable abrasion tester is designed to determine the ability of an optical fiber cable sheath and marking to resist abrasion.
Specifications
|
Abrading stroke for sheath |
10 mm |
|
|
Abrading stroke for markings |
Method 1 |
Method 2 |
|
|
40 mm |
100 mm |
|
Abrading stroke cycles |
1 ~ 9999 times |
|
|
Abrading frequency |
55 ± 5 cycles/min |
|
IEC-60794-1-2-F1 Optical fiber cable temperature cycling chamber
Application
Optical fiber cable temperature cycling chamber is designed to apply temperature cycling on optical fiber cables in order to determine the stability behavior of the attenuation of cables submitted to temperature changes. It features large test chamber, precise temperature control as well as low temperature fluctuations.
Specifications
|
Model |
HST Series |
|||
|
|
HST-40100 |
HST-70100 |
HST-40150 |
HST-70150 |
|
Temp. range |
-40°C ~ 100°C |
-70°C ~ 100°C |
-40°C ~ 150°C |
-70°C ~ 150°C |
|
Temperature control accuracy |
± 0.5°C |
± 0.1°C |
||
|
Temperature measuring accuracy |
± 0.5°C |
|||
|
Temperature fluctuation |
± 0.5°C |
± 2°C |
||
|
Temperature uniformity |
≤2.0 |
|||
|
Heating up speed (empty) |
≥3.0 /min |
|||
|
Cooling down speed (empty) |
≥0.7-1 /min |
|||
|
Interior dimension(W×D×H) Exterior dimension(W×D×H) |
2000 × 2500 × 2000 mm 2300 x 4500 x 2600 mm |
1000 × 1000 ×1000 mm 1600 x1600 x 1600 mm |
||
|
Open door (WxDxH) one of a pair |
1000 mm x 2000mm |
1000 mm x 1000 mm |
||
|
Chamber weight |
Approx. 2000 kg |
Approx. 1000 kg |
||
|
Interior material |
Stainless steel plate(SUS304) |
|||
|
Exterior material |
Stainless steel plate(SUS304) |
|||
|
Insulation |
Rigid foam |
|||
|
Refrigeration system |
Hermetic compressor, single stage refrigeration system. |
|||
|
Display |
LCD |
|||
1000mm Optical fiber cable flexing testing machine
Application
Optical cable flexing tester determines the ability of an optical fiber cable to withstand repeated flexing for elevator cable and similar application. Test confrims to IEC 60794-1-2-E8 standard.
Specifications
|
Technical Parameters |
|
|
Model |
HST-GQR-1000 |
|
Carriage Stroke |
1000 mm |
|
Maximum Impact Cycles |
1-9999 cycles |
|
Speed setting Range |
250-350 mm/min |
Fiber Cable And Wire Tensile Testing Machine Cable Torsion Tester/Cable Testing Equipment
Application
GLQ-1000 Optical Fiber Cable Repeated Bending Tester is used to determine the ability of a fiber optic cable to
withstand repeated bending (cyclic flexing).
Optical Fiber Cable Impact Tester Series allows a cable sample to be bent backwards and forwards at an
angle of 180° by bending extreme ends of cables at 90° in opposite directions, while the sample is
subjected to a tensile load.
The bending arm is designed to hold the cable securely during the entire test, without crushing the optical
fibers or inducing optical loss. The bending radius is controlled by replaceable cushioning reels, chosen
T o match the cable bending radius. The machine is capable of cycling at a rate of 30 cycles per minute.
Specifications
|
Technical Parameters |
|
|
Model |
GLQ-1000 |
|
Bending angle |
±90° |
|
Maximum bending cycles |
1-9999 cycles |
|
Frequency range |
10 - 30 cycles / min |
|
Bending radius |
75,100,125, 150, 175, 200, 225, 250, 275, 300, 375 mm (others upon request) |
|
Mass of weights for applying tension |
1-10 kg (other upon request) |
Our company is a leading specialist manufacturer and supplier in China. Serving for more than 150 countries and regions. is specialized in developing and manufacturing testing equipments for metal ,non-metal and composite materials with all kinds of testing standards of GB,ISO,ASTM,BS, EN etc.
Production meets the European standards and international quality control, obtains certificates such as CE/FDA/ISO9001/SGS
The company occupies an area of 23,500 square meters and has a construction area of 19,800 square meters. It has a comprehensive office building, scientific research office building, electrical installation and debugging building, assembly shop, heavy machine workshop, machine shop, blanking workshop and painting. Production and office facilities such as workshops, cold work workshops, measurement rooms, and product showrooms. The annual production capacity of the test machine can reach more than 1,500 units.
We sincerely welcome customers from home and abroad to visit us, let's make progress together and reach win-win cooperation!
Certificate
All products has been guaranteed by European CE certificate, Germany TUV certificate, ISO9001:2000 ...
warranty :
1. 2 years warranty for machine host. English technical to door service
2.English manual and Video CD for machine using and maintenance.We offer free training in our factory, welcome to visit and learn more about our machines.
3.Free accessories :Software ,manual, book, cd videos, USB control .
After-sales service:
Training to install (3 options):
A. We will supply the machine with training video and user's manual in English for installing, operation, maintenance and trouble-shooting, and shall give technical guide by e-mail, fax, telephone/MSN/ICQ and so on, when you meet some problems of installation, using or adjusting.
B. You can come to our factory for training. We will offer professional guide. Direct and effective face-to-face training.all sorts of tools and testing facility,we will also provide accomadation during training period.
){kind=link}